WONDERFUL METAL · CUSTOM ALUMINUM FENCING
72x72 Black Aluminum Semi & Full Privacy Fence Panels
Shape a quieter-looking backyard, patio or property boundary with a black aluminum privacy fence designed around your space. Choose spaced horizontal slats for filtered views, or a closed infill layout for stronger visual screening.
The 72 × 72 inch format—6 ft wide × 6 ft high—provides a useful starting point for modular fence planning. Wonderful Metal supplies custom panels, coordinated posts and matching gates for contractors, distributors and residential projects.
UNDERSTAND THE SIZE
What Does a 72 × 72 Fence Panel Mean?
A 72x72 black aluminum fence panel generally refers to a nominal 72-inch width and 72-inch height. Each dimension equals 1828.8 mm. It is also commonly described as a 6x6 black aluminum privacy fence panel or a 6 ft × 6 ft aluminum fence panel.
For ordering, specify whether the width refers to the panel frame, the clear opening between posts, or the complete installed module. These measurements are different. A nominal 1800 × 1800 mm panel is approximately 70.87 × 70.87 inches and should not be treated as an exact 72 × 72 inch replacement.
TWO WAYS TO CREATE PRIVACY
Semi Privacy or Full Privacy?
Black Semi Privacy Aluminum Fence
Horizontal slats with deliberate gaps provide a lighter appearance and allow some views, daylight and airflow through the panel. This arrangement suits garden boundaries, terraces and outdoor spaces where complete screening is unnecessary.
Specify the gap between slats rather than relying on the words “semi privacy.” Visibility changes with slat width, gap size, viewing angle and lighting.
Explore horizontal slat fencing →Black Full Privacy Aluminum Fence
A closed, overlapping or interlocking infill arrangement is intended to block direct views through the main panel area. It suits backyard seating areas, courtyard boundaries and service screens where visual separation matters most.
Check edge details, joints and the clearance below the fence when evaluating privacy. A closed fence also needs careful assessment of posts, fixings and wind exposure.
View the 6 ft × 6 ft privacy panel →| Selection point | Semi privacy | Full privacy |
|---|---|---|
| Slat arrangement | Open gaps between slats | Closed or overlapping infill |
| Visual screening | Partial; depends on spacing and angle | Higher screening through the infill |
| Outdoor appearance | Open, linear and light | Continuous architectural surface |
| Typical locations | Gardens, terraces, landscape divisions | Backyards, courtyards, seating areas |
| Structural planning | Review the complete system for local exposure | Give particular attention to wind loads and foundations |
MATERIAL & FINISH
Aluminum Construction with a Black Powder-Coated Finish
Aluminum does not develop red rust like unprotected carbon steel and does not rot like timber. It offers a practical option for outdoor boundaries where appearance and routine maintenance both matter.
Specify the aluminum alloy, temper, profile dimensions and wall thickness in the purchase specification. These details should match the panel span, connection design and site conditions rather than being selected by appearance alone.
Matte black creates a restrained finish alongside brick, render, stone and landscaping. Confirm the black color reference, gloss level and texture against an approved sample. For coastal locations, discuss pretreatment, coating suitability and cleaning requirements before ordering.
72x72 Privacy Fence Panel Specification Checklist
Use the following as a quotation checklist. Custom details and supply scope are confirmed before production.
| Article | Details to confirm |
|---|---|
| Nominal format | 72 in W × 72 in H / 6 ft W × 6 ft H; exact finished dimensions by approved drawing |
| Privacy style | Spaced semi privacy slats or closed full privacy infill |
| Profilés en aluminium | Alloy, temper, slat section, rail dimensions and wall thickness |
| Finition de surface | Black powder coating; sample-approved color, texture and gloss |
| Articles | End, line, corner and gate posts; sizes and reinforcement as required |
| Mounting method | Embedded posts or base-plated posts on a suitable structural substrate |
| Connections | Compatible brackets, fasteners, caps and installation clearances |
| Portails assortis | Pedestrian or driveway designs with separately specified frames and hardware |
| Order configuration | Pre-assembled panels or a component kit, subject to selected design |
| Packing and shipping | Panel protection, component identification and destination-specific freight quotation |
Plan the Complete Fence Line
Posts, Corners & Ground Conditions
Count each end, corner and gate position separately. Post spacing follows the approved panel-and-bracket arrangement. For sloping ground, agree on a stepped layout or a purpose-designed solution; do not assume a rigid privacy panel can rack.
Footing dimensions and base anchors depend on soil, substrate, fence height and local loads. A patio slab or retaining-wall cap may need separate assessment before supporting a privacy fence.
Matching Gates & Access
Coordinate gate height, slat direction, finish and privacy level with adjacent panels. Gate openings require separate hinge, latch and operating clearances, and gate posts may need a different design from ordinary line posts.
Browse our fence and gate range, then send the required clear opening and preferred swing or sliding operation with your layout.
From Layout to Installation
- Measure the boundary. Record straight runs, corners, elevation changes, access openings and existing structures.
- Select the privacy level. Confirm slat spacing or closed infill, including the desired appearance from both sides.
- Approve the drawings. Verify dimensions, post positions, connection details and the complete material list.
- Prepare the supports. Set out and install foundations or anchors to the approved site-specific design.
- Install and inspect. Fit panels, check alignment, tighten hardware as specified and test gate operation.
Keep powder-coated surfaces protected during installation. Clean the fence with mild soap, water and a soft cloth, rinsing away grit and salt deposits. Avoid abrasive pads and check hardware periodically.
Custom Manufacturing for Contractors & Wholesale Buyers
Wonderful Metal was established in 2021, with an office in Qingdao and a factory in Linqu, Shandong. For a coordinated project order, request panels, posts, matching gates and installation components against the same approved drawings.
For distributor or contractor purchases, identify repeat panel sizes, special-width sections, preferred packaging and any labeling requirements. Ask for the current minimum order quantity, sample arrangements, production schedule and freight scope with your enquiry.
What Affects the Price?
The cost of a 72x72 black aluminum privacy fence panel depends on the profile weight, infill layout, coating specification, assembly method, order quantity and included hardware. Posts, gates, packing, freight and destination charges should be clearly itemized so quotations can be compared on the same basis.
A panel-only price is different from the cost of a complete installed fence. Send your fence-line drawing and delivery destination to receive a quotation with a defined supply scope.
Foire aux questions
Is 72x72 the same as a 6x6 fence panel?
Yes. 72 inches equals 6 feet. Confirm whether the advertised dimensions are nominal or finished panel dimensions before ordering.
Can a semi privacy panel be made in the same size as a full privacy panel?
Request both options in the same nominal format. The selected profiles, gaps and connection system must be checked before the final dimensions are approved.
Does full privacy mean there are no visible gaps anywhere?
It describes the main infill arrangement. Edge joints, post connections and the clearance above the ground can still affect sightlines. Review the complete assembly drawing.
Are posts and brackets included?
The quotation should state this explicitly. Request an itemized list of panels, posts, caps, brackets and fasteners, with gate hardware listed separately.
Is a full privacy fence suitable for a windy property?
Suitability depends on the complete system and site conditions. Ask for the posts, connections and foundations to be assessed for the applicable wind requirements; panel size alone does not establish a wind rating.
Can I order custom widths and matching black gates?
Wonderful Metal offers customization. Send your required panel sizes, gate openings, finish preference and quantities so the proposed configuration can be confirmed.
START WITH YOUR FENCE LAYOUT
Request Your 72x72 Black Aluminum Fence Quote
Tell us whether you need semi privacy or full privacy panels. Include your total fence length, exact size requirements, gate openings, quantity and delivery city or port. Add a drawing or reference photo to help define the slat layout and supply scope.
Send Your RequirementsView Existing 6x6 Product
